數控平面磨床工作臺面使用和保養事項

數控平面磨床在使用完畢切斷電源后，由于余磁的作用，加工的工件不易從工作臺面上取下，所以需要把控制磁力的開關轉換到退磁的位置，多次反復直到使得余磁完全消失，然后取下工件；

對于大工件，當其與工作臺面接觸面積較大時，結束磨削后，由于余磁以及光滑表面的吸附力，使得工件取出比較困難，這個時候，我們不可以強硬拖拽，可以使用木棒、銅棒或者合適的工具輕輕將工件扳動后再慢慢取下，避免劃傷工作臺面或者劃傷工件；

我們在磨床上裝夾工件時，要確保工件放置的位置覆蓋的絕磁層條數盡可能多，保證充分利用磁力，加固工件，此外，工件盡量放置于工作臺面中央，大工件還需要在其周圍放上擋塊放置移動；

平面磨床工作臺面要保持平整光滑，定期修修磨，有垃圾時需要用油石或者紗布拋光；

數控平面磨床結束工作后，需要將工作臺面擦拭干凈，臺面不得出現嚴重磕碰，避免破壞其精度，長時間不使用數控平面磨床時，我們要將工作臺面擦拭干凈并涂上防銹油；

SKM7380數控臥軸圓臺平面磨床工作臺面